- 您现在的位置：买卖IC网 > Sheet目录1238 > RDK-160 (Power Integrations)KIT REF DESIGN LINKSWITCH 2
LNK603-606/613-616
Parameter
Symbol
Conditions
SOURCE = 0 V; T J = 0 to 100 °C
(Unless Otherwise Specified)
Min
Typ
Max
Units
Output
LNK6X3
I D = 50 mA
LNK6X4
T J = 25 ° C
T J = 100 ° C
T J = 25 ° C
24
36
24
28
42
28
ON-State
Resistance
R DS(ON)
I D = 50 mA
LNK6X5
T J = 100 ° C
T J = 25 ° C
36
16
42
19
W
I D = 62 mA
LNK6X6
I D = 82 mA
T J = 100 ° C
T J = 25 ° C
T J = 100 ° C
24
9.6
14
28
11
17
OFF-State
Leakage
Breakdown
Voltage
I DSS1
I DSS2
BV DSS
V DS = 560 V See Figure 20
T J = 125 ° C See Note 3
V DS = 375 V See Figure 20
T J = 50 ° C
T J = 25 ° C
See Figure 20
700
15
50
m A
V
DRAIN Supply
Voltage
50
V
Auto-Restart
ON-Time
t AR-ON
t ON × I FB = 2 mA- m s, f OSC = 12 kHz
V FB = 0
See Notes 1, 5
450
ms
Auto-Restart
OFF-Time
t AR-OFF
1.2
2
s
Open-Loop
FEEDBACK Pin
Current Threshold
Open-Loop
ON-Time
I OL
See Note 5
See Note 5
-120
90
m A
m s
NOTES:
1. Auto-restart ON-time is a function of switching frequency programmed by t on x I FB and minimum frequency in CC mode.
2. The current limit threshold is compensated to cancel the effect of current limit delay. As a result the output current stays constant
across the input line range.
3. I DSS1 is the worst case OFF state leakage specification at 80% of BV DSS and maximum operating junction temperature. I DSS2 is a
typical specification under worst case application conditions (rectified 265 VAC) for no-load consumption calculations.
4. When the duty-cycle exceeds DC MAX the LinkSwitch-II operates in on-time extension mode.
5. This parameter is derived from characterization.
6. Mechanical stress induced during the assembly may cause shift in this parameter. This shift has no impact on the ability of
LinkSwitch-II to meet ±10% in mass production given the design follows recommendation in AN-44 and good manufacturing practice
7. The switching frequency is programmable between 60 kHz and 85 kHz.
10
Rev. F 01/10
www.powerint.com
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
RDK-236
KIT REF DESIGN PFS714EG
RECE-20279-001E-01
RCPT IPEX MHF
RF2594-000
BD540-30
RF2873-000
POLYSWITCH 1.25A RESET FUSE RAD
RGEF1000-1
POLYSWITCH PTC RESET 10A HOLD
RGEF1000-2
POLYSWITCH PTC RESET 10A HLD T/R
RGEF1000K
POLYSWITCH PTC RESET 10A KINK
RGEF1100-2
POLYSWITCH PTC RESET 11A HLD T/R
相关代理商/技术参数
RDK-189
功能描述:KIT REF DESIGN FOR PLC810 RoHS:是 类别:编程器，开发系统 >> 评估板 - DC/DC 与 AC/DC（离线）SMPS 系列:HiperPLC™ 产品培训模块:Obsolescence Mitigation Program 标准包装:1 系列:True Shutdown™ 主要目的:DC/DC，步升 输出及类型:1，非隔离 功率 - 输出:- 输出电压:- 电流 - 输出:1A 输入电压:2.5 V ~ 5.5 V 稳压器拓扑结构:升压 频率 - 开关:3MHz 板类型:完全填充 已供物品:板 已用 IC / 零件:MAX8969
RDK-193
功能描述:LED 照明开发工具 LED Drvr Ref Des LinkSwitch-PH RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
RDK-194
功能描述:电源管理IC开发工具 LED Drvr Ref Des LinkSwitch-PH RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
RDK-195
功能描述:LED 照明开发工具 RefDesign 90-265V.5A OutputLinkSwitch-PH
RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装:
RDK-201
功能描述:电源管理IC开发工具 LinkSwitch CV Reference Design Kit RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
RDK-203
功能描述:电源管理IC开发工具 Audio Amp Pwr Supply 90-265V PeakSwitch RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V
RDK-236
功能描述:交流/直流开关转换器 HiperPFS Ref Des Kit 347W PFC, 380VDC RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel
RDK-239
功能描述:LED 照明开发工具 HV 150W RESONANT CONVERTER KIT RoHS:否 制造商:Fairchild Semiconductor 产品:Evaluation Kits 用于:FL7732 核心: 电源电压:120V 系列: 封装: